
Flat roofing and TPO in Edmond and Oklahoma City
A flat roof leaks where water sits and where seams open. We repair and replace flat roofs on shops, offices, porches and additions with TPO, a single-ply membrane whose seams are heat welded into one continuous sheet, fasten the edges where wind pulls hardest, and slope the roof to its drains so water leaves instead of standing.
- Every seam heat welded
- Edges and corners fastened for wind
- Water sent to the drains, not the office
Tell us about the flat roof
We answer the same day. The night of a storm, we answer until the last tarp is down.
Shingles gone and rain coming in right now? Call or text: 405-555-0147
Why we put down TPO, and why the seams matter most
On a flat roof, water does not run off quickly the way it does on shingles. It moves slowly, and wherever it stops, it looks for a way in. The weak points are the seams between sheets, the patches from years of repairs, and the joints around drains, vents and rooftop units.
TPO answers that with heat-welded seams. Each overlap is run with a hot-air welder that melts the two sheets into one, and we probe every seam after it cools to find any gaps. Around curbs, pipes and drains we weld flashing from the same membrane, so the whole roof is one material.
The white surface also reflects the summer sun, which keeps the membrane and the rooms under it cooler. One Oklahoma City shop owner had patched her roof for years; after the new TPO went down, the water went to the drains instead of the office.
“Our shop's flat roof had been patched for years. Briarstone put down a new TPO roof, welded every seam, and the water now goes to the drains instead of the office.”

The details that keep a flat roof dry
The membrane gets the attention, but these are what decide whether it lasts.
Slope to the drains
Tapered insulation under the membrane gives a flat roof just enough fall to move water to the drains and scuppers.
Edges fastened for wind
Wind lifts a flat roof hardest at the perimeter and the corners, so the membrane is fastened more closely there.
Metal at the parapets
Coping along the top of the parapet walls and metal edge where there is none, fastened so the wind cannot peel it.
Flashing at every curb
Rooftop units, vents and pipes get welded TPO flashing, not a bead of sealant that dries out in the sun.
Patch it, or put down a new roof?
We check the membrane and the insulation under it before we price.
| What we find | Usually | Why |
|---|---|---|
| One split seam or puncture on a sound roof | Repair | The rest of the membrane is still doing its job |
| Failed flashing around a rooftop unit | Repair | The joint failed, not the roof |
| Water standing in the same spots after rain | Fix the slope | Patches over ponding water fail again |
| Wet insulation across large areas | Replace | Wet insulation stays wet under a patch |
| Years of patches over an old roof | Replace | Every patch is another seam to fail |
How a flat roof job goes
We do flat roofs across Edmond, Oklahoma City, Moore, Norman, Yukon and Guthrie.
Walk it after rain, if we can.
Standing water shows us where the slope is wrong.
Check the insulation underneath.
A few small cores tell us if it is dry or soaked.
Written estimate.
Membrane, insulation, drains, edge metal and flashing, each on its own line.
New roof down, every seam welded and probed.
Then a final walk with you, and dated photos of the finished roof.
Flat roofing questions we hear most
What is TPO?
A single-ply roofing membrane that comes in wide rolls, usually white. Where two sheets overlap, we melt them together with a hot-air welder, so the seam becomes part of the sheet instead of a glued joint that can open later.
Why does my flat roof keep leaking in the same place?
Usually because water stands there. Ponding water finds every weak seam and patch, and each freeze and thaw works at it. The lasting fix is to get the water moving to a drain or scupper, often with tapered insulation, and not just another patch.
Can you repair a flat roof instead of replacing it?
Often, yes. A split seam, a punctured spot or failed flashing around a rooftop unit can be repaired if the rest of the membrane is sound and the insulation under it is dry. If the insulation is wet across large areas, a patch will not last, and we show you where with the photos.
Do you work on homes too, or only businesses?
Both. We put TPO on shops and small offices, and on low-slope porches, carports and additions on homes, where shingles do not belong because the pitch is too low for them to shed water.
Does a flat roof need a permit?
It depends on the town and the building. Oklahoma City's re-roof permit ordinance covers single-family homes and duplexes; commercial buildings follow their own process. We check with the city for every flat roof before we start.
Cal walks the flat roof before he writes a number
Need the pitched part of the building looked at too? See roof repair or, after a storm, storm and wind damage.

Cal Brannigan, owner and roofer
Cal answers the phone, gets on the roof and writes the estimate. On a FORTIFIED job he photographs every stage the evaluator needs to see.
Book a flat roof visit
We answer the same day. The night of a storm, we answer until the last tarp is down.
Shingles gone and rain coming in right now? Call or text: 405-555-0147

Flat roof leaking again? Tell us where it pools.
The address, what the building is used for and where the water shows up inside. A photo of the roof after rain helps.
Book a free wind and storm check
We answer the same day. The night of a storm, we answer until the last tarp is down.
Shingles gone and rain coming in right now? Call or text: 405-555-0147